Hits: 1,995
Category: Software » Graphic » Engineering Design
CSI Perform 3D A special program with a special focus on seamless firewall design. Using this program, it is possible to analyze complex structures including shear structures in a nonlinear manner based on different degrees of resistance and deformation. The geometry of the model can be read from the SAP2000 or ETABS program. In the program, various types of elements can be used: beams, curtains, shear walls (with openings), slabs, dampers and separators. Non-linear analyzes can be done either statically or dynamically on a model. Loads can be applied at various stages to structures. For example, the dynamic load of an earthquake can be entered after a nonlinear static load. The program has powerful capabilities for design based on performance and can calculate the required capacity ratios for all components and for extreme states. Performance evaluation is performed automatically based on ATC-40, FEMA-356 and ATC-440.Macs are a timeline.
A key feature of the software CSI Perform 3D:
modeling:
- Refreshing geometry model of the program SAP 2000 and ETABS
- the Mac modeling with any number of elements
- elements of linear and non-linear
- ease of use of the graphics program
- beam elements, columns and Brackets
- Shear links and Panel Zone
- Shear walls with pop
- ups - Flush failures -
Floor slabs
- Fluid nozzles
- Friction separators
- Plastic joints with PMM interactions
- P-Delta effects
Non - linear analysis:
- Pushover static analysis
- Three-dimensional non-linear time histories analysis
- Use of fiber-reinforced sections for various materials
- Determination of nonlinear capacities based on deformation or resistance
- Performing nonlinear dynamical analysis after nonlinear static analysis
- Considering nonlinear static
analysis of automatic analysis circles :
- Considering the power relation - the trilinear shift
- in consideration Reducing hardness under cyclic loads
- Calculating energy dissipation
- Analyzing P-Delta
- Loading from different earthquakes
- Modifying the resistance of members without changing the model
- Efficient
performance analysis engine for large structures Performance based on evaluation:
- Nonlinear static analysis based on ATC- 40, FEMA-356-440 and ATC
- limit states based on the deformation, deformation resistance or relative
- relative Capacity / need
- Calculate the ratio of capacity / need for multiple earthquakes
- Calculation of deformation or resistance capacities for various types of elements
- Calculation of energy balance for energy losses
:
- Characterization of color charts Capacity / requirement ratios
- Response charts for ATC-40, FEMA-356 and ATC-440
- Transformation time history results , Relative deformation and forces
- View the history of the response forces for a group of elements
- Bending and bending diagrams
- Displaying force for a group of elements
- View geometry deformed in motion
- View animated
mody forms
- Hysteresis cycle diagrams - Charts Energy Balance
CSI Perform 3D A special program with a special focus on seamless firewall design. Using this program, it is possible to analyze complex structures including shear structures in a nonlinear manner based on different degrees of resistance and deformation. The geometry of the model can be read from the SAP2000 or ETABS program. In the program, various types of elements can be used: beams, curtains, shear walls (with openings), slabs, dampers and separators. Non-linear analyzes can be done either statically or dynamically on a model. Loads can be applied at various stages to structures. For example, the dynamic load of an earthquake can be entered after a nonlinear static load. The program has powerful capabilities for design based on performance and can calculate the required capacity ratios for all components and for extreme states. Performance evaluation is performed automatically based on ATC-40, FEMA-356 and ATC-440.Macs are a timeline.
A key feature of the software CSI Perform 3D:
modeling:
- Refreshing geometry model of the program SAP 2000 and ETABS
- the Mac modeling with any number of elements
- elements of linear and non-linear
- ease of use of the graphics program
- beam elements, columns and Brackets
- Shear links and Panel Zone
- Shear walls with pop
- ups - Flush failures -
Floor slabs
- Fluid nozzles
- Friction separators
- Plastic joints with PMM interactions
- P-Delta effects
Non - linear analysis:
- Pushover static analysis
- Three-dimensional non-linear time histories analysis
- Use of fiber-reinforced sections for various materials
- Determination of nonlinear capacities based on deformation or resistance
- Performing nonlinear dynamical analysis after nonlinear static analysis
- Considering nonlinear static
analysis of automatic analysis circles :
- Considering the power relation - the trilinear shift
- in consideration Reducing hardness under cyclic loads
- Calculating energy dissipation
- Analyzing P-Delta
- Loading from different earthquakes
- Modifying the resistance of members without changing the model
- Efficient
performance analysis engine for large structures Performance based on evaluation:
- Nonlinear static analysis based on ATC- 40, FEMA-356-440 and ATC
- limit states based on the deformation, deformation resistance or relative
- relative Capacity / need
- Calculate the ratio of capacity / need for multiple earthquakes
- Calculation of deformation or resistance capacities for various types of elements
- Calculation of energy balance for energy losses
:
- Characterization of color charts Capacity / requirement ratios
- Response charts for ATC-40, FEMA-356 and ATC-440
- Transformation time history results , Relative deformation and forces
- View the history of the response forces for a group of elements
- Bending and bending diagrams
- Displaying force for a group of elements
- View geometry deformed in motion
- View animated
mody forms
- Hysteresis cycle diagrams - Charts Energy Balance
modeling:
- Refreshing geometry model of the program SAP 2000 and ETABS
- the Mac modeling with any number of elements
- elements of linear and non-linear
- ease of use of the graphics program
- beam elements, columns and Brackets
- Shear links and Panel Zone
- Shear walls with pop
- ups - Flush failures -
Floor slabs
- Fluid nozzles
- Friction separators
- Plastic joints with PMM interactions
- P-Delta effects
Non - linear analysis:
- Pushover static analysis
- Three-dimensional non-linear time histories analysis
- Use of fiber-reinforced sections for various materials
- Determination of nonlinear capacities based on deformation or resistance
- Performing nonlinear dynamical analysis after nonlinear static analysis
- Considering nonlinear static
analysis of automatic analysis circles :
- Considering the power relation - the trilinear shift
- in consideration Reducing hardness under cyclic loads
- Calculating energy dissipation
- Analyzing P-Delta
- Loading from different earthquakes
- Modifying the resistance of members without changing the model
- Efficient
performance analysis engine for large structures Performance based on evaluation:
- Nonlinear static analysis based on ATC- 40, FEMA-356-440 and ATC
- limit states based on the deformation, deformation resistance or relative
- relative Capacity / need
- Calculate the ratio of capacity / need for multiple earthquakes
- Calculation of deformation or resistance capacities for various types of elements
- Calculation of energy balance for energy losses
:
- Characterization of color charts Capacity / requirement ratios
- Response charts for ATC-40, FEMA-356 and ATC-440
- Transformation time history results , Relative deformation and forces
- View the history of the response forces for a group of elements
- Bending and bending diagrams
- Displaying force for a group of elements
- View geometry deformed in motion
- View animated
mody forms
- Hysteresis cycle diagrams - Charts Energy Balance
required system
Specifications
Manufacturer: Computers and
Structures, Inc
File Size: 131 MB Release Date: 10:45 - 1396/11/15 | 2018.02.04 Source: PC Download / www.p30download.ir Rating:
File Size: 131 MB Release Date: 10:45 - 1396/11/15 | 2018.02.04 Source: PC Download / www.p30download.ir Rating:
Installation guide
1. Install the software.
2. Run the Keygen.exe file to create a file named lservrc.
3. Copy the created file to the software installation location * and copy it to the default path.
2. Run the Keygen.exe file to create a file named lservrc.
3. Copy the created file to the software installation location * and copy it to the default path.
C: \ Program Files (x86) \ Computers and Structures \ PERFORM-3D 7 \ PERFORM-3D 7 \ Program
* Software installation location: The installation location folder is usually located in the Windows drive and within the Program Files folder. You can also find the installation location in this way:
- In Windows XP: After installation, right-click on the shortcut in the Start menu and click Properties, and then click Find Target.
- In Windows 7: After installation, right-click on the shortcut in the Start menu and click on the Open file location option.
- In Windows 8: After installation, right-click on the Shortcut on the Start Screen and click on the Open file location option, in the window that opens, right-click on the shortcut of the software and click Open file location click.
- On Windows 10: After installation, right-click Shortcut on the Start menu and click on the Open file location option, in the window that opens, right-click on the Shortcut software and click on the Open file location button. do.
- In Windows XP: After installation, right-click on the shortcut in the Start menu and click Properties, and then click Find Target.
- In Windows 7: After installation, right-click on the shortcut in the Start menu and click on the Open file location option.
- In Windows 8: After installation, right-click on the Shortcut on the Start Screen and click on the Open file location option, in the window that opens, right-click on the shortcut of the software and click Open file location click.
- On Windows 10: After installation, right-click Shortcut on the Start menu and click on the Open file location option, in the window that opens, right-click on the Shortcut software and click on the Open file location button. do.
download links
File password
www.p30download.com
Dear Students, It's important to learn and earn experience
No comments:
Post a Comment